Troubleshooting Smartcard issus on Department of Health (DoH) Enduro 3E Printers

Modified on Fri, 11 Mar, 2022 at 4:57 PM

Use the info below as a reference to help troubleshooting the Green or Blue Department of Health ID Printers which are a rebranded Magicard Enduro 3E printer.


Correct driver and firmware files can be downloaded from this Magicard page


https://support.magicard.com/solution/support-for-department-of-health-green-printers/


Printers usually have the HID Omnikey 5321, 5121, or 5122 combi (dual) encoder fitted.


The New Magicard 300 DoH has the Elatec Encoder fitted.


There are 2 systems used with the DoH printers called SPINE and EPIC


The Doh Printers must have the correct printer and smart card drivers installed. Windows will load its own Smart card Microsoft driver, If this happens the contact and contactless encoders may not appear in HID Omnikey Workbench utility.

This means the SPINE or EPIC System will not be able to encode cards.


SIMPLE FIX = Please try using Google Chrome instead of Internet Explorer 11.

 

*********************************************************************************************************************************************

 

Installing and testing the OEM (DoH Enduro 3e -Green) printer models;

 

You can the installer (executable) here;

 

https://doh.magicard.com/

 

Or the bare driver files here;

 

https://support.magicard.com/solution/network-admin-magicard-ultradriver-bare-files/

 

Once the driver is installed, connect the printer on USB.


Please run through the attached checklist (win_10_checklist.pdf).

These points are important not only on Windows 10, but all operating systems.

They will ensure the printer always has ‘status’.


Smart Card Reader


As well as the USB (type B) socket on the back of the printer, there is a trailing USB cable on this model.

This connects directly to the HID Omnikey 5321 dual encoder.

If the encoder isn’t connected (via the trailing USB cable),

then spurious encoder jam error messages may be seen on the printer.


On the new DoH 300 it will only have one USB cable for both the printer and smart card encoder.

 

 

To check the Smart card reader on the Green or Blue DoH printers follow these steps...


In Devices & Printers, right-click on the printer icon.

 

Choose Printer Properties -> Tools

 

1. Set the encode mode: SEMPLATEN (contactless) / SEMDEFAULT (contact)

2. Load a card from the hopper to the encode position: GEM

3. Once the card is in the encoding position, select which encoder to look at within the HID Omnikey Workbench;

 

OMNIKEY CardMan 5x21 0              Contact

OMNIKEY CardMan 5x21-CL 0        Contactless

 

4. Eject the card:  EJT

 


Each step is described in more detail below..



In Devices & Printers, right-click on the printer icon.

 

Choose Printer Properties -> Tools

 

Setting the SMART Encode Mode (SEM);

 

To set contactless encoding position (SEM)  type the following quick command into the Quick Commands box;

 

SEMPLATEN

 

Then click Send

 

cid:image018.png@01D69675.EFBB7C30

 

To set contact encoding position (SEM)  type the following quick command into the Quick Commands box;

 

SEMDEFAULT

 

Then click Send

 

cid:image003.png@01D69672.0DEBBE80

 

Loading a card from the hopper to the encoding position;

 

To load a card from the rear card hopper to the encoding position, type the following into the Quick Commands box;

 

GEM

 

Then click Send

 

cid:image015.png@01D69676.5D583EE0

 

Ejecting a card from the printer;

 

To eject a card from within the printer, type the following into the Quick Commands box;

 

EJT

 

Then click Send

 

cid:image019.png@01D69676.D05C1010

 

Checking you have comms with the card (contact / contactless);

 

Download and install the HID Omnikey Workbench (currently V1.6.0.0) from HID’s support website here;

 

https://www.hidglobal.com/drivers/29454

 

When the HID Omnikey Workbench is opened, you should see two encoders (one contact, the other contactless);

 

cid:image021.png@01D69677.8DDBB870

 

If you don’t see any encoders (or only one), and ensuring the trailing lead from the printer is also connected to a USB port on the PC;

 

Run the Unattended MSI driver installer here (this will force Windows 10 to use the HID driver rather than its own);

 

https://www.hidglobal.com/drivers/29765

 

After running the above MSI installer.

In device manager you should see the following;

 

 

 

NHS Digital Article on setting up DoH printer.


https://digital.nhs.uk/services/registration-authorities-and-smartcards/care-identity-service/news-and-service-updates/registration-authority-user-guides/how-to-set-up-a-registration-authority-workstation

Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select at least one of the reasons
CAPTCHA verification is required.

Feedback sent

We appreciate your effort and will try to fix the article